Communicate with Supplier? Supplier
John chang Mr. John chang
What can I do for you?
Chat Now Contact Supplier
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
Home> Blog> esign of digital trigger for three-phase thyristor semi-controlled bridge

esign of digital trigger for three-phase thyristor semi-controlled bridge

November 23, 2018

I. Introduction

The three-phase thyristor bridge type semi-controlled rectifier circuit can control the DC output voltage of the rectifier circuit by changing the control angle of the trigger circuit of the thyristor under the condition that the AC power supply voltage is constant. The circuit is medium-sized. Rectifiers or applications that do not require reversible electric drag systems are more widely used. The traditional three-phase bridge half-controlled rectifier circuit requires three independent analog triggers to trigger the thyristor. Because of the complicated circuit, difficult adjustment and low reliability of the analog trigger, this paper proposes a The digital flip-flop circuit composed of 80C196KC single-chip microcomputer greatly simplifies the control circuit. The generated trigger pulse has the characteristics of wide phase shifting range, high control precision, fast dynamic response, stable and reliable performance, and its performance index is better than analog trigger. .

Second, the circuit composition and principle analysis

1. The digital flip-flop of the three-phase thyristor half-controlled Bridge Rectifier circuit is composed of the minimum system of 80C196KC MCU, synchronous detection circuit and pulse power amplifier circuit, as shown in Figure 1. The microcontroller 8 0 C 1 9 6 KC, latch, 27C256 program memory, 62C256 data memory constitutes the minimum system. The 80C196KC is a 16-bit high-performance single-chip microcomputer from Intel Corporation. Its power consumption is extremely low. In addition to normal operation, it can also operate in both standby and power-down modes. Its working speed is several times higher than that of the 51 MCU. The bus width is 8/16 bits optional and the internal width is always 16 bits. 80C196KC contains 8 10-bit A/D converters, 512 bytes of RAM, 2 hardware timers/counters, one monitor tracking timer, and the crystal oscillator is 12MHz. The single-chip microcomputer is formed according to the difference between the given and feedback signals. The phase shift pulse with the control angle α is output from the HS0.0~0.2 pin.

Design of digital trigger for three-phase thyristor semi-controlled bridge

2. Synchronous signal detection consists of opto-isolation, comparator and shaping circuit (Figure 2). When the zero-crossing of the line voltage UAC sent by the synchronous transformer, a square wave is generated at the output of the opto-isolator, which is shaped by the inverter U1 and differentiated by the RC circuit to generate a pulse as an external interrupt signal to the EXTINT end of the 80C196KC. , to achieve the trigger pulse and power synchronization. In order to simplify the circuit, the system adopts a relative trigger mode, which only needs single-phase synchronization.

Design of digital trigger for three-phase thyristor semi-controlled bridge

3. Pulse power amplifier circuit. As shown in Figure 3, in order to achieve reliable triggering of large inductive loads, the trigger circuit uses a pulse sequence triggering method. The pulse output from the single-chip port HS0.0~0.2 is sent to the pulse cluster forming circuit consisting of 555. After being amplified by the FET and separated by the pulse transformer, it is output to the trigger pole of the thyristor.

Design of digital trigger for three-phase thyristor semi-controlled bridge

Third, the control angle algorithm

The thyristor control angle α is obtained by the following equation:

Design of digital trigger for three-phase thyristor semi-controlled bridge

In the case of a large inductive load, the relationship between the output voltage Ud of the three-phase half-controlled bridge rectifier circuit and the control angle α is:

Design of digital trigger for three-phase thyristor semi-controlled bridge

The above equation shows that the output current Id and the control angle α of the three-phase half-controlled bridge rectifier circuit are nonlinear, and the equation (1) is based on linearization, so it must be corrected by the following formula:

Design of digital trigger for three-phase thyristor semi-controlled bridge

In order to simplify the procedure, the control angle α is obtained by using U to give a -ω-α' lookup table. Since the A/D converter of the MCU is 10 bits, the given voltage of 5V is 3FFH=1023 after A/D conversion. If it is divided into 51 files, then:

Design of digital trigger for three-phase thyristor semi-controlled bridge

So ω=33H corresponds to the given voltage U=5V; when U=4.9V, the binary number is 1003H, then:

Design of digital trigger for three-phase thyristor semi-controlled bridge

The rest of the analogy, which is exactly 0. 1 V corresponds to 0 1 H, 0.2 V corresponds to 02H, ..., etc., which is convenient for table lookup.

A zero-crossing detection circuit generates a sync pulse at a synchronous voltage UAC from a negative half wave to a positive half-wave zero-crossing. Since the UAC lags behind the phase voltage UA30°, the timing at which the sync pulse occurs is exactly the natural commutation point of the phase A voltage. The natural commutation points of each phase of A, B, and C are 120° different from each other. When the natural commutation point of phase A is found, the natural commutation points of the other B and C phases are different from each other at T/3, T is The second measured voltage period can be obtained by measuring the time interval between two adjacent sync pulses.

Let 2 T and 1 T be the time when the synchronization pulse appears and the time when the last pulse appeared. When 1 T 》 1 T, then:

Design of digital trigger for three-phase thyristor semi-controlled bridge

The software timer is started at the natural commutation point of each phase (the tuning time is αt), and the time when the software timer expires is the timing at which the phase emits a trigger pulse (control angle α).

The phase shift range of the three-phase bridge type semi-controlled rectifier circuit with large inductive load is 0~180°. When the control angle α is greater than 120°, the adjacent two thyristor trigger circuits may work at the same time, so each thyristor must have its own trigger circuit in the analog trigger circuit. Since a single-chip microcomputer can only form a digital trigger circuit, in order to make the three-phase circuit share a trigger circuit, we must limit the control angle α to within 120°. This can be done by changing the triggering order.

When α1 2 0°, VT1 should be triggered at 120°~240°, then VT2 and VT3 should be triggered every 120°, but VT3 can be triggered by α'=α-120° at 0~120°, over 120°. Later, VT is triggered by α'. 1. Obviously the two are equivalent, but after this processing, the control angle can be limited to 120°, and a flip-flop can be shared.

Contact Us

Author:

Mr. John chang

E-mail:

info@yzpst.com

Phone/WhatsApp:

8613805278321

Popular Products
You may also like
Related Information
Thyristor

The full name thyratron, commonly known as thyristor, is a bistable power electronic device that contains 3 or more PN junctions that can switch from off-state to on-state or from on-state to...

Judgment of thyristor damage causes

When the thyristor damage need to check the analysis of the reasons, the core can be removed from the cooling jacket, open the core box and then remove the chip, observe the signs of damage to...

Radiator thermal resistance, thyristor dissipated power test method

A special sealing device is made by the method of disposing the dust in the radiator. This kind of device only leaves the fan through hole. Go to the construction site and construction site to...

Talking about the method of thyristor overcurrent protection

In order to prevent damage to the thyristor caused by the failure of the AC circuit inversion of the thyristor, the traditional method is to use a fast fuse for overcurrent protection. The advantage...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

Contact Us

Author:

Mr. John chang

E-mail:

info@yzpst.com

Phone/WhatsApp:

8613805278321

Popular Products
Blog News
Thyristor

August 14, 2023

Home

Product

Whatsapp

About Us

Inquiry

苏ICP备05018286号-1
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send