Communicate with Supplier? Supplier
John chang Mr. John chang
What can I do for you?
Chat Now Contact Supplier
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
YANGZHOU POSITIONING TECH CO., LTD.
Home> Blog> Design Scheme of Thyristor Control Circuit Based on TSC/TCR Type Arc Suppression Coil

Design Scheme of Thyristor Control Circuit Based on TSC/TCR Type Arc Suppression Coil

December 07, 2018

0 Preface

Single-phase ground faults are the most common faults in power systems. When a single-phase earth fault occurs in a neutral point ungrounded network, it can be operated with a fault for 2 hours. However, if the capacitance to ground in the power grid is large (such as cable lines), a large arc will be formed at the grounding point, posing a threat to the safe operation of the power system. The arc suppression coil can be used to reliably extinguish the arc. The design scheme of the thyristor control circuit based on TSC/TCR arc suppression coil proposed in this paper is tested by experimental circuit, and the effect is satisfactory. The feasibility of the scheme is verified.

1 TSC/TCR arc suppression coil structure and working process

The TSC and TCR circuits compensate the capacitive current of the grid by changing the inductive reactance value of the secondary side of the arc suppression coil, thereby changing the inductance of the arc suppression coil in the system.

TSC (Thyristor Switched capacitor) is the thyristor switching capacitor.

It consists of three capacitors with a capacity ratio of 1:2:4 and a thyristor switch. By controlling the on and off of the thyristor, the capacitance value of the secondary side input changes according to a certain law. This adjustment is graded and not continuous.

TCR (Thyristor Controlled Reactor) is a thyristor control reactor consisting of a reactor and a thyristor switch. By controlling the firing angle of the thyristor, the equivalent reactance is changed. Its current varies continuously within a certain range.

The capacitance current value of the power grid is measured by the arc suppression coil controller, and the capacitance value and the inductance amount to be input are calculated. The capacitance is input by the TSC control circuit, and the reactance is input by the TCR trigger circuit. The control circuits of TSC and TCR will be analyzed separately.

TSC/TCR arc suppression coil principle structure diagram

2 TSC control circuit

2.1 Voltage zero crossing detection

The capacitor will have a large inrush current during the switching process, damaging the thyristor. Therefore, the input AC voltage should be equal to the residual voltage on the capacitor, that is, when the voltage across the thyristor is zero, it will be triggered for the first time. The zero-crossing detection circuit can output a zero-crossing pulse when the input signal crosses zero, as shown in Figure 2.

Voltage zero crossing detection circuit

It can be seen that the sinusoidal signal passes through the uncontrollable rectifier bridge, and a sine wave with a period of π in the upper half of the cycle is generated at point B. After the op amp is compared with a voltage close to zero, a pulse at the zero point is generated at point C. As shown in Figure 3.

Zero-crossing detection circuit waveform


Contact Us

Author:

Mr. John chang

E-mail:

info@yzpst.com

Phone/WhatsApp:

8613805278321

Popular Products
You may also like
Related Information
Thyristor

The full name thyratron, commonly known as thyristor, is a bistable power electronic device that contains 3 or more PN junctions that can switch from off-state to on-state or from on-state to...

Judgment of thyristor damage causes

When the thyristor damage need to check the analysis of the reasons, the core can be removed from the cooling jacket, open the core box and then remove the chip, observe the signs of damage to...

Radiator thermal resistance, thyristor dissipated power test method

A special sealing device is made by the method of disposing the dust in the radiator. This kind of device only leaves the fan through hole. Go to the construction site and construction site to...

Talking about the method of thyristor overcurrent protection

In order to prevent damage to the thyristor caused by the failure of the AC circuit inversion of the thyristor, the traditional method is to use a fast fuse for overcurrent protection. The advantage...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

Contact Us

Author:

Mr. John chang

E-mail:

info@yzpst.com

Phone/WhatsApp:

8613805278321

Popular Products
Blog News
Thyristor

August 14, 2023

Home

Product

Whatsapp

About Us

Inquiry

苏ICP备05018286号-1
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send